Brake Disc Lathe

keithsfleet

Anyone know anywhere in South Dublin preferably Tallaght, Firhouse, Knocklyon area that can lathe a disc?

jimgoose

Howard Engineering in Glasnevin can machine just about anything, by all accounts.

keithsfleet

Yes they'd been mentioned to me but bit of a trek, was hoping for somewhere nearer. Thanks though.

Greyfoot

Try Trident Engineering, they in Clondalkin, do all kinds of machining jobs.

colm_mcm

Pretty sure all toyota dealers have these now maybe try tadg riordans?

dr.fuzzenstein

Brake discs are fairly inexpensive. By the time they have a fairly pronounced lip, they would be approaching minimum thickness and possibly warped.
Rather than pay for them to be lathed, you'll be better off buying new discs and throwing them in.
I thought things like lathing discs and maybe even grinding down brake pads where gone since 1974.
Plus the old discs can be sharpened round the edges and be used as a James Bond Frisbee! Fun! :P;)

dashcamdanny

Any engineering shop should be able to do this .

Rathcoole is close to Tallaght.

http://ceartateo .ie/

kirving

Know nothing about this crowd, but I'm from the area and knew that there was some engineering firm just off the Firhouse road. http://industrialengineering.ie/

Any local community school would have a couple of lathes, but I'm not sure if the engineering department would be even allowed to help you out, even if you were to pay for it.

keithsfleet

Cheers for the replies.

I'm picking to have it machined as the car is only 4 years old and one disc is badly scraped from a have a go Harry trying to replace the pads by removing the caliper and bracket together, unsuccessfully, attempting to refit it at the querest angle with the aide of a lump Hammer and driving it 2km to me with the top of the brake pad backing plate being the only point of contact with the rotor.

The mind does be boggled

Guy:Incognito

Are you actually going to save anything over a new disc though?

Personally , even for a bit extra I'd rather new discs.

DuckSlice

I don't see the point in skimming them unless they are high performance.

greasepalm

for safety new discs and pads.

rex-x

Kevin Irving wrote: »

Know nothing about this crowd, but I'm from the area and knew that there was some engineering firm just off the Firhouse road. http://industrialengineering.ie/

Any local community school would have a couple of lathes, but I'm not sure if the engineering department would be even allowed to help you out, even if you were to pay for it.

The issue with disc skimming is you must cut both faces together, you cant do one side turn it around and do the other :eek:
So the amount of places that can do this are very limited, and besides you only have maybe 2mm of total wear on a disc before it becomes scrap anyway so new discs really is what you should be getting OP

dashcamdanny

rex-x wrote: »

The issue with disc skimming is you must cut both faces together, you cant do one side turn it around and do the other :eek:
So the amount of places that can do this are very limited, and besides you only have maybe 2mm of total wear on a disc before it becomes scrap anyway so new discs really is what you should be getting OP

I served my time as a lathe turner/miller and always did one face at a time. Very simple quick job.

I cant see any benefit from doing to sides together other than production speed. Heat is not really a factor as they get much hotter with heavy breaking while driving.

Is there a particular reason you say it must be done this way?

It has become uneconomical to do it now due to the cheapness of new disc these days.

rex-x

You cant get the runout to be within spec if you turn the disc around on the lathe, it will cause vibration through the pedal.
As a turner surely you know that once your work piece is set up in the 4 jaws and runout adjusted accordingly you do not touch it until machining is finished unless you must machine the end covered by the chuck, you cant just lob them into a 3 jaw chuck and skim away *shudders*

All commercial machines cut both sides for this reason, a quick google will reveal thousands of hits telling you why

dashcamdanny

rex-x wrote: »

You cant get the runout to be within spec if you turn the disc around on the lathe, it will cause vibration through the pedal.
As a turner surely you know that once your work piece is set up in the 4 jaws and runout adjusted accordingly you do not touch it until machining is finished unless you must machine the end covered by the chuck, you cant just lob them into a 3 jaw chuck and skim away *shudders*

All commercial machines cut both sides for this reason, a quick google will reveal thousands of hits telling you why

I always used a DTI to set it up on a 4 jaw and used the dti again of the machined face to match it up. Perfectly. It takes no time with a bit of experience. It runs perfectly true. It really not that big of a deal.

Set them up on both 3 and 4 jaw chucks. . Never ever has one come back. Saying that. Have not done one in 8 years.

jca

rex-x wrote: »

You cant get the runout to be within spec if you turn the disc around on the lathe, it will cause vibration through the pedal.
As a turner surely you know that once your work piece is set up in the 4 jaws and runout adjusted accordingly you do not touch it until machining is finished unless you must machine the end covered by the chuck, you cant just lob them into a 3 jaw chuck and skim away *shudders*

All commercial machines cut both sides for this reason, a quick google will reveal thousands of hits telling you why

No need to use the 4 jaw chuck to skim discs the 3 jaw is perfectly fine if you use a dial gauge on the central diameter that's on the hub. I did them years ago but no one does them now because since the abolition of asbestos in brake pads the discs wear much more now.

dashcamdanny

jca wrote: »

No need to use the 4 jaw chuck to skim discs the 3 jaw is perfectly fine if you use a dial gauge on the central diameter that's on the hub. I did them years ago but no one does them now because since the abolition of asbestos in brake pads the discs wear much more now.

Yeah . I felt like I was a bit out of the loop there using a 3 jaw all of a sudden. With the sudder comment.

But then again. Self centering chucks are as accurate as anyone would need for 99.9 % of anything.