Advertisement
If you have a new account but are having problems posting or verifying your account, please email us on hello@boards.ie for help. Thanks :)
Hello all! Please ensure that you are posting a new thread or question in the appropriate forum. The Feedback forum is overwhelmed with questions that are having to be moved elsewhere. If you need help to verify your account contact hello@boards.ie
Hi there,
There is an issue with role permissions that is being worked on at the moment.
If you are having trouble with access or permissions on regional forums please post here to get access: https://www.boards.ie/discussion/2058365403/you-do-not-have-permission-for-that#latest

Immersion heater question

  • 24-10-2013 12:34am
    #1
    Fred Swanson
    Closed Accounts Posts: 21,730 ✭✭✭✭


    This post has been deleted.


Comments

  • #2
    Billy Bunting
    Registered Users, Registered Users 2 Posts: 2,842 ✭✭✭Billy Bunting


    You may have a small leake, dripping taps ??

    or, the thermostat is set too low.


  • #3
    Fred Swanson
    Closed Accounts Posts: 21,730 ✭✭✭✭Fred Swanson


    This post has been deleted.


  • #4
    SB6
    Registered Users, Registered Users 2 Posts: 68 ✭✭SB6


    there is a thermostat on the element itself. Comes set from factory usually around 70 degrees so unless someone tampered with it that should be grand.

    Another thing is the build up of limescale or something on the element. Do you live in hard water area or are you off the mains?


  • #5
    Fred Swanson
    Closed Accounts Posts: 21,730 ✭✭✭✭Fred Swanson


    This post has been deleted.


  • #6
    SB6
    Registered Users, Registered Users 2 Posts: 68 ✭✭SB6


    Where do you test the temp of the water after the hour you mention in the first post?


  • Advertisement
  • #7
    Fred Swanson
    Closed Accounts Posts: 21,730 ✭✭✭✭Fred Swanson


    This post has been deleted.


  • #8
    Tokyo
    Registered Users, Registered Users 2 Posts: 22,656 ✭✭✭✭Tokyo


    Fred Swanson wrote: »
    This post has been deleted.

    Have you put your hand on the cylinder or the outgoing pipes after an hour? You'll tell pretty quickly if the tank is lukewarm or not....


  • #9
    SB6
    Registered Users, Registered Users 2 Posts: 68 ✭✭SB6


    mike_ie wrote: »
    Have you put your hand on the cylinder or the outgoing pipes after an hour? You'll tell pretty quickly if the tank is lukewarm or not....

    +1

    Just going by experience if the water in the tank is cold to begin with then 3kw for an hour, even if everything is in order won't cut it anyway. Thats probably why people do have 5kw immersions with a 3kw side for 'sink' and an extra 2kw switched on at the same time for 'bath' to make things quicker.


  • #10
    Fred Swanson
    Closed Accounts Posts: 21,730 ✭✭✭✭Fred Swanson


    This post has been deleted.


  • #11
    Tokyo
    Registered Users, Registered Users 2 Posts: 22,656 ✭✭✭✭Tokyo


    Fred Swanson wrote: »
    This post has been deleted.

    Not necessarily, but I'd be putting my hand on the tank after an hour and seeing how hot it is. If it's piping hot at the tank and your missus is still getting lukewarm water, you have a problem down the line. If the cylinder is lukewarm, it might need a bit more time. Or the thermostat in the immersion itself might be set too low.


  • Advertisement
  • #12
    Fred Swanson
    Closed Accounts Posts: 21,730 ✭✭✭✭Fred Swanson


    This post has been deleted.


  • #13
    SB6
    Registered Users, Registered Users 2 Posts: 68 ✭✭SB6


    Dont know how helpful this is or accurate but doing a bit of experimenting, if the initial temp of the water in the tank is 1o degrees then heating a 200 litre tank to 45 degrees (suitable for a bath??) will take 3hr or a 250l tank nearly 4.

    If the starting temp of the water is 20 degrees then heating water to 45 in 200 litre tank is 2 hr 20 min and 250 tank is nearly 3hr

    ROUGH calculations

    .......thats with your 3kw's


Advertisement