Advertisement
If you have a new account but are having problems posting or verifying your account, please email us on hello@boards.ie for help. Thanks :)
Hello all! Please ensure that you are posting a new thread or question in the appropriate forum. The Feedback forum is overwhelmed with questions that are having to be moved elsewhere. If you need help to verify your account contact hello@boards.ie
Hi there,
There is an issue with role permissions that is being worked on at the moment.
If you are having trouble with access or permissions on regional forums please post here to get access: https://www.boards.ie/discussion/2058365403/you-do-not-have-permission-for-that#latest

Cadence sensor won't stick

  • 27-03-2013 9:38pm
    #1
    Registered Users, Registered Users 2 Posts: 4,475 ✭✭✭


    I got a cadence sensor with my Garmin, and after my cycle on Saturday when I couldn't get it to work, I noticed that the magnet you attach to the pedal arm was dislodged and hanging down, only the ziptie I'd attach stopping it from landing somewhere between here and Cork city. Evidently, the sticky back hadn't worked very well, but I'm loathe to try anything more permanent, like super glue or something.

    I bought some more zipties, and was considering just tying a few more on, but I can't be the only one with a non-functioning magnet sticky bit? Is it a failure on the part of this component, and I'd be better off bringing it back to the shop?


Comments

  • Registered Users, Registered Users 2 Posts: 4,559 ✭✭✭The tax man


    Try these. I have them, they work grand and are unseen. Best of all they WILL NOT fall off, in fact they're tricky to remove.

    I've never had a problem with the original magnets coming loose. You could also just buy some strong double sided pads in a hardware and cut it to size and try again.


  • Registered Users, Registered Users 2 Posts: 1,100 ✭✭✭clog


    +1 for Taxmans suggestion above works perfectly.


  • Registered Users, Registered Users 2 Posts: 4,830 ✭✭✭doozerie


    I'd try the magnet on pedal axle option too, but if it doesn't work for you or if you'd just prefer to stick with your current magnet then double-sided carpet tape (might have another name too) is another alternative to sticky pads. Rolls of it should be readily available in hardware stores, it's relatively strong, and because it's thin and on comes in a lengthy roll it's very useful for a range of things.


  • Registered Users, Registered Users 2 Posts: 335 ✭✭bikermartin


    i have fixed mine with the cabletie and then wrapped it in standard insulating tape. it would not lie flush with the crank any other way.its not what you may want on an expensive bike, but has stayed in place on mine for 6 months now even over the worst of the winter :rolleyes:


  • Registered Users, Registered Users 2 Posts: 4,475 ✭✭✭corblimey


    So just to be clear, I don't need the magnet that came with the Garmin? Any old magnet in the right position will do the job, it's the sensor on the fork that does the actual work, right?


  • Advertisement
  • Registered Users, Registered Users 2 Posts: 4,833 ✭✭✭niceonetom


    Any sufficiently strong magnet - I experimented with a button magnet from the back of a fridge ornament and it wasn't strong enough to give a reliable signal or hold itself to the axle.

    Maplin sell neodymium magnets in a few sizes that do the job nicely.


  • Registered Users, Registered Users 2 Posts: 68,317 ✭✭✭✭seamus


    The sticky bit is crap. Stick a small piece of rubber - cut a square out of an old tube - between the crank arm and the magnet and tighten up the zip tie. This will stop the magnet from moving on the crank arm.


  • Registered Users, Registered Users 2 Posts: 1,103 ✭✭✭2 Wheels Good


    corblimey wrote: »
    So just to be clear, I don't need the magnet that came with the Garmin? Any old magnet in the right position will do the job, it's the sensor on the fork that does the actual work, right?
    Yeah, a Cateye cadence magnet or equivalent should also do the trick. Same for the wheel for anyone with oddly shaped spokes.


Advertisement