Technical Graphics Junior Cert 2010:Monday 21st of June 9:30-12:30

bevan619

Daniel2oo9 wrote: »

Hes Great at it.I Got 55% in the pre ordinary level:rolleyes:

I'm screwed tomorrow. My folder's still in school

Daniel2oo9

HAHAHHA Im nt studingg

Tommyrawr

i got 49% in the pre but the drawings i drew were just 1 ticked and no actuall real correcting like the mistakes or anything i got 20 for them Proabably attempt so should i drop to pass tommrow? and have i everything covered in pass?

Gentlemanne

so how did everybody do?

Ellipse/Parabola (Boat logo)- easy. Got all the little details like the rudder and the tandent okay

Isometric Scale (Boiler?)- really easy. No trouble at all

Translation, central symmetry etc. (Butterfly logo)- easy enough but a bit confusng. By the time I got to rotation I messed something up and the lines ddnt go through the centre of the circle (P4) but it was okay.

Orthographic projection (Castle)- prettyhard, glad I left it last. Got a bit done

Overall I'd say it was a pretty easy exam. Some lad put his short question answer booklet on my desk and I almost looked in it thinking t was mine, but I noticed his exam number on the front which he wrote in red pen :pac:

Closed ac

I thought it was kinda hard. Q1, Q2 & Q5 were easy.

I barely had any time to do Q6 but it was hard anyway.

The short questions were ok too.

Hoping for a B.

.SONIC.

Gentlemanne wrote: »

so how did everybody do?

Ellipse/Parabola (Boat logo)- easy. Got all the little details like the rudder and the tandent okay got it okay, messed up on m!!

Isometric Scale (Boiler?)- really easy. No trouble at all ruined this

Translation, central symmetry etc. (Butterfly logo)- easy enough but a bit confusng. By the time I got to rotation I messed something up and the lines ddnt go through the centre of the circle (P4) but it was okay. got this kinda messed up the rotation

Orthographic projection (Castle)- prettyhard, glad I left it last. Got a bit done pretty easy made up the surface of s!! :D

Overall I'd say it was a pretty easy exam. Some lad put his short question answer booklet on my desk and I almost looked in it thinking t was mine, but I noticed his exam number on the front which he wrote in red pen :pac:

all in all i think it went good!!!

youngcardinal

I did crap in this but I'm finished now so I don't really care haha!

whistlin_boy

Did Q2 (rotation), Q4 (solids in contact), Q5 (transformation geometry) and Q6 (ellipse and parabola).

Reckon I did okay, solids in contact was a bit confusing.....draw a development of one slanted side, but other than that it was fine:D;):D.

mista_2k10

Were should the new position of the rotation have been? Because I think I did it wrong

kevin12345

mista_2k10 wrote: »

Were should the new position of the rotation have been? Because I think I did it wrong

Above the image

mista_2k10

kevin12345 wrote: »

Above the image

Yes!, I done it right so

Luno

I only done 3 long questions I spent ages trying to do the axonametric but it didn't work!
I done the elipse - Was pretty good happiest with it anyways!
Rotation - Easy just is a pain rotating every single point I mean it doesn't prove anything does it?

Overall I done pretty crap! I don't care though didn't touch a book and now I never have to do tech graph again so I think it's I that win!

Gaeilge-go-deo

M&S* wrote: »

Rotation - Easy just is a pain rotating every single point I mean it doesn't prove anything does it?

Ya rotating every single point.. there was loads! i had to use symbols so i could understand which was which :L

Luno

Gaeilge-go-deo wrote: »

Ya rotating every single point.. there was loads! i had to use symbols so i could understand which was which :L

Haha it's like first letters then numbers then after that SYMBOLS! :pac:

Gaeilge-go-deo

M&S* wrote: »

Haha it's like first letters then numbers then after that SYMBOLS! :pac:

ya there isnt enough numbers to label all the points lol

Gentlemanne

all you had to do was rotate four points of the circle? the top, bottom left hand side and right hand side

kevin12345

Gentlemanne wrote: »

all you had to do was rotate four points of the circle? the top, bottom left hand side and right hand side

Is that how you do it? Oh I divide the circle up using my 30/60 degree set square then bring up the points:D

Gaeilge-go-deo

Gentlemanne wrote: »

all you had to do was rotate four points of the circle? the top, bottom left hand side and right hand side

I was on about Q2 .. the Rotation question .. haa

Luno

Gaeilge-go-deo wrote: »

I was on about Q2 .. the Rotation question .. haa

Eh but it was a circle? It wouldn't be a very accurate one if you only took four?

Gentlemanne

M&S* wrote: »

Eh but it was a circle? It wouldn't be a very accurate one if you only took four?

sure it would, you only need to use the compass on those points anyway to make the butterfly.

Luno

Gentlemanne wrote: »

sure it would, you only need to use the compass on those points anyway to make the butterfly.

Butterfly? What? Haha I taught we were on about the rotations question am I wrong?

kevin12345

M&S* wrote: »

Butterfly? What? Haha I taught we were on about the rotations question am I wrong?

No Mary your not wrong that's what we are talking about :pac: He/she thinks we're on about the transformations

Luno

kevin12345 wrote: »

No Mary your not wrong that's what we are talking about :pac: He/she thinks we're on about the transformations

So confused! But that's not a new thing for me in tech graph, I didn't do the transformations question so it's even more confusing..

It's over and we can all relax! :cool:

Gentlemanne

oops lol I ignored all the other questions because dont know how to do those, and the transformation question has a rotaton at the end

Luno

Gentlemanne wrote: »

oops lol I ignored all the other questions because dont know how to do those, and the transformation question has a rotaton at the end

Yeah but we were talking the just rotation one not transformation geometry..

Kells...

we tables that are at a slant for junior next year