Copper Sheet Material Supplier.

kadman

I,m looking for a supplier of copper sheet material for something I,m working on at the moment. Sheet thickness of about .5m, and 300mm wide, and 600mm long, or longer.

If someone could point me in the right direction, I,d appreciate it. thanks

kadman

Chorcai

It will cost you but try Amari in Dublin. http://www.amari-ireland.com/, Copper prices have gone up alot !

kadman

Chorcai wrote: »

It will cost you but try Amari in Dublin. http://www.amari-ireland.com/, Copper prices have gone up alot !

I,ll check them out Monday. thankyou:)

kadman

Chorcai

kadman wrote: »

I,ll check them out Monday. thankyou:)

kadman

Does it have to be copper or just a copper colour ? Acess Plastics do alot of stuff other than plastics, aliminumum sheets, plactic sheets with a metal face. They are in Ashbourne, any of the Daves (I think theres 3 !!) will help ya out, all dead on guys.

kadman

Chorcai wrote: »

Does it have to be copper or just a copper colour ? Acess Plastics do alot of stuff other than plastics, aliminumum sheets, plactic sheets with a metal face. They are in Ashbourne, any of the Daves (I think theres 3 !!) will help ya out, all dead on guys.

Has to be copper I,m afraid. Thanks

kadman

stoneill

Robert A. Copeland & Sons Ltd.
Coppersmiths
Dunshaughlin Industrial Estate.

They supply copper in sheets, rolls, strips etc. for roofing.
Could be what you are looking for.

kadman

Chorcai wrote: »

It will cost you but try Amari in Dublin. http://www.amari-ireland.com/, Copper prices have gone up alot !

I received a fast reply , prices, sizes ect today from Amari. Great start.

kadman

kadman

Picked my sheet of copper, 2000x1000x0.7 up today. 142 euros including vat.
They have every conceivable metal material in there. Expensive, but it fits the bill for me

kadman

Fingalian

Kadman
Do you know if they sell Brass bar and rod?
Thanks
F.

Chorcai

Fingalian wrote: »

Kadman
Do you know if they sell Brass bar and rod?
Thanks
F.

Yea they do all that as well.

Dave_D

For brass, I used these guys. Seemed fairly decent.

http://www.jameshealy.ie/

Chorcai

Dave_D wrote: »

For brass, I used these guys. Seemed fairly decent.

http://www.jameshealy.ie/

I used to go to them alot years ago, the Cork branch, some craic you'd have with the lads !

website :eek:

kadman

Chorcai wrote: »

I used to go to them alot years ago, the Cork branch, some craic you'd have with the lads !

website :eek:

Website is what put me off them straight away. It says unprofessional to me on first impressions. They need to tweak it a bit.....NO.......A LOT:D

kadman

Chorcai

kadman wrote: »

Website is what put me off them straight away. It says unprofessional to me on first impressions. They need to tweak it a bit.....NO.......A LOT:D

kadman

haha just a tad, still wouldnt put me off.

wipednwired

Hey folks,

I need a small piece of copper sheet - 14mm x 14mm in dimension, and between 1.2mm and 1/5mm thick. Preferred grade is C101, because it's for electrical conductivity (I'm modifying my laptop).

Does anyone know where I can find this in or near Dublin? I tried Amari, but they only do large sheets, which would be way too costly. The guy at Amari suggested a sheet metal fabricator, but this is so outside of my world that I don't even know where to start...

Any ideas greatly suggested! I'm trying to think broadly - are there stores that would sell this kind of thing for other purposes?

Thanks

Dave_D

How about copper pipe. just cut it open and hammer it flat. Use a blow torch if it work hardens. You could then rub it on different grades of sandpaper to polish it up and flatten it more if needed. Start off with coarse, and end up around 600 grit or higher.

breadandjam

Try the model shop near the bottom of capel st or Mark's models in Hawkin's street