Advertisement
If you have a new account but are having problems posting or verifying your account, please email us on hello@boards.ie for help. Thanks :)
Hello all! Please ensure that you are posting a new thread or question in the appropriate forum. The Feedback forum is overwhelmed with questions that are having to be moved elsewhere. If you need help to verify your account contact hello@boards.ie
Hi there,
There is an issue with role permissions that is being worked on at the moment.
If you are having trouble with access or permissions on regional forums please post here to get access: https://www.boards.ie/discussion/2058365403/you-do-not-have-permission-for-that#latest

Fawlty Amplifier

  • 27-03-2007 8:39am
    #1
    DJ Donie
    Closed Accounts Posts: 6 ✭


    How ye! I've just started off a mobile disco and I bought this amplifier on ebay. Its a XXL Pro-480 Amp with 480W power. The problem is, theres only one side of the amp working, the right side. Therefore, all the power is going from one side of the amp and onto one speaker, and then that speaker is connected to the next speaker.

    Is there any chance of my amp blowing? I went to get it repaired but the fecker didnt repair it.


Comments

  • #2
    electro.ie
    Registered Users, Registered Users 2 Posts: 167 ✭✭electro.ie


    bring it back dude and get him to repair it properly.

    The answer is in the impedance of the loudspeakers. Impedance gives a measure of how much electrical current the loudspeaker draws. Without getting too technical on electricity, look at it like this - the amplifier 'offers' a voltage to the loudspeaker. The loudspeaker draws a current, which may be lesser or greater according to the the impedance of the loudspeaker. The amplifier has no way of forcing a current into a loudspeaker other than by offering a higher voltage.

    Loudspeaker designers have over the years settled on certain standard impedance ratings - 15, 8 and 4 ohms. The 15 ohm loudspeaker will draw the least current and the 4 ohm loudspeaker the most. Connected to the same amplifier, the 4 ohm loudspeaker will be loudest.

    The amplifier has an output impedance too, but this is usually just a tiny fraction of an ohm. Although in the past it was common to match output and input impedances, this no longer has any relevance.

    More important is the amplifier's ability to supply current. It can offer the voltage no problem, but can it live up to the loudspeaker's current demand?

    You will find this information in the specification of the amplifier. Often a manufacturer will state that the amplifier will drive loads down to 2 ohms. This means that you can connect two 4 ohm loudspeakers or four 8 ohm loudspeakers in parallel. ('In parallel' means that both the terminals of each loudspeaker are connected directly to the terminals of the amplifier - the signal does not go through one loudspeaker before reaching another. The parallel connection might, confusingly, be made inside one of the speaker cabinets by means of a 'loop through' connector).

    Stick within the manufacturer's ratings and all will be well.

    If you tried to connect a heavier load (i.e. lower impedance, or more loudspeakers wired in parallel) to this amplifier, then there are three possibilities. If the amplifier is well designed, all should still be well, but you will find that you don't actually get a louder sound; it is shared among the speakers. Also, if the amplifier is well designed, then it may be the case that it automatically goes into a protection mode. You will not get optimum output in this mode. If the amplifier is not well designed... well, you can guess the consequences!

    As a general rule, two loudspeakers per amplifier channel is usually OK.
    but again man just send it back to be repaired


  • #3
    DJ Donie
    Closed Accounts Posts: 6 ✭DJ Donie


    Cheers For That Mate!!! :)


Advertisement