Advertisement
If you have a new account but are having problems posting or verifying your account, please email us on hello@boards.ie for help. Thanks :)
Hello all! Please ensure that you are posting a new thread or question in the appropriate forum. The Feedback forum is overwhelmed with questions that are having to be moved elsewhere. If you need help to verify your account contact hello@boards.ie

Worklog: ...another man's treasure

  • 02-05-2010 9:24pm
    #1
    Registered Users Posts: 183 ✭✭crótach


    Starting off on a new project, it's been 4 years since I built my last PC and I've spent the hibernation on a laptop. It's time for a change and I picked up a good few items on adverts to start me off:

    Silverstone TJ-07 case
    Xeon X5550 processor
    Corsair Dominator 6GB RAM
    Powercolor PCS+ 5870 graphics card

    Just finished with the bottom part of the case and will post pictures soon :)


Comments

  • Registered Users Posts: 183 ✭✭crótach


    Finished with the bottom section... sorta

    The rad is in place, along with the PSU, and I sleeved the cables running from the front of the case.

    4576492072_5195d7d388.jpg

    I put a carpet tile in the bottom of the case to reduce vibrations and mounted the rad using velcro, it fits perfectly:
    4576492114_f5356d9e12.jpg

    I finally got to use the old Danger Den fillport. Had this thing about 6-7 years! The case gave me tons of trouble tho, it's way too thick, I spent about 30 minutes drilling the hole for it:
    4576492144_651b0298fb.jpg

    Gotta sleeve tons of cables, that's gonna be some fun. I already burnt two of my fingers :) At least Nils' girlfriend sent me an easter bunny:
    4576492156_62295e564d.jpg


  • Registered Users Posts: 183 ✭✭crótach


    Not much interest here so I'll just post the photos of the finished project. I've clocked the CPU up to 4.4 GHz, but for 24/7 I'm keeping it at 4.0 GHz - it requires a lot less voltage and runs much cooler.

    4609215392_9bee5423bc_m.jpg4609215368_f1b5c0b604_m.jpg
    4609215400_efdb6eeec8_m.jpg4609215378_e0ec1c73b9_m.jpg
    4609215370_9f0596873b_m.jpg4609215384_57e49dbb49_m.jpg4609215370_9f0596873b_m.jpg
    4608873749_5b32ac670b_m.jpg4608873807_86e70c4cab_m.jpg




  • Thanks for sharing :)
    Very nice single loop and exceptional cabling job, well done.
    Would appreciate posting some temperatures and voltages on your oc if you have time.


  • Registered Users Posts: 183 ✭✭crótach


    Hiya. To run the CPU at 4.0 GHz it requires 1.3v. To get it to 4.4 GHz stable I had to push it to 1.55v which doesn't sit too well with me for 24/7. Luckily Asus motherboard allows storing 8 different profiles, so I have all the settings available to be used on demand.

    Temperatures are 39-40C idle, 64-69C full load (8 threads LinX full memory). Prime testing gives temps of 5C less or thereabouts. These are realtemp values, BIOS values around 30C which is plain ridiculous :)

    I haven't OCed the graphics card yet, but that's coming soon. AFAIK the new PCBs have digital PWMs and don't allow adjusting voltage, so I probably won't get more than a 50-100 Mhz overclock on it, but that's ok.

    The beast runs nice and quiet, Scythe S-Flex 120mm fan was by far the loudest component in the system and it's been slowed down to 50% using the mCuber Tbalancer and now fits well. (running at about 8.4v)

    Loop parts:
    Thermochill 140.3
    Laing DDC 3.25
    EK Supreme HF
    EK 5870 FC v2
    EK Multioption 250
    DD Fillport
    Primochill LRT tubing


Advertisement